Процессы СМК
Наша компания в процессе своей работы использует следующие стандарты:
Обозначение |
Заголовок |
Язык |
РВД И ПРОМЫШЛЕННЫЕ РУКАВА |
||
BS EN 854:2015 |
Rubber hoses and hose assemblies. Textile reinforced hydraulic type. Specification |
ENG |
BS EN 856:2015 |
Rubber hoses and hose assemblies. Rubber-covered spiral wire reinforced hydraulic type. Specification |
ENG |
DIN EN 853:2015 |
Rubber hoses and hose assemblies. Wire braid reinforced hydraulic type. Specification |
ENG |
BS EN 857:2015 |
Rubber hoses and hose assemblies. Wire braid reinforced compact type for hydraulic applications. Specification |
ENG |
BS ISO 3862:2020 |
Rubber hoses and hose assemblies. Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids. Specification |
ENG |
BS ISO 4079:2020 |
Rubber hoses and hose assemblies. Textile-reinforced hydraulic types for oil-based or water-based fluids. Specification |
ENG |
BS ISO 4397:2011 |
Fluid power connectors and associated components. Nominal outside diameters of tubes and nominal hose sizes |
ENG |
BS EN ISO 18752:2022 |
Rubber hoses and hose assemblies. Wire- or textile-reinforced single-pressure types for hydraulic applications. Specification |
ENG |
BS ISO 1436:2020 |
Rubber hoses and hose assemblies. Wire-braid-reinforced hydraulic types for oil-based or water-based fluids. Specification |
ENG |
ISO 11237 |
Rubber hoses and hose assemblies — Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification |
ENG |
SAE J517_202007 |
Hydraulic Hose
|
ENG |
SAE J1273_202110 |
Recommended Practices for Hydraulic Hose Assemblies
|
ENG |
SAE J1401_201302 |
Road Vehicle - Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids |
ENG |
J1406_201207 |
Application of Hydraulic Brake Hose to Motor Vehicles - Wheel End and Axle |
ENG |
ГОСТ 6286-2017 |
РУКАВА РЕЗИНОВЫЕ ВЫСОКОГО ДАВЛЕНИЯ С МЕТАЛЛИЧЕСКИМИ ОПЛЕТКАМИ БЕЗ КОНЦЕВОЙ АРМАТУРЫ. |
RUS |
ГОСТ ISO 1436-2020 |
РУКАВА РЕЗИНОВЫЕ И РУКАВА В СБОРЕ. РУКАВА ГИДРАВЛИЧЕСКИЕ С МЕТАЛЛИЧЕСКИМИ ОПЛЕТКАМИ ДЛЯ ЖИДКОСТЕЙ НА НЕФТЯНОЙ ИЛИ ВОДНОЙ ОСНОВЕ |
RUS |
ГОСТ ISO 8331-2016 |
РУКАВА РЕЗИНОВЫЕ И ПЛАСТИКОВЫЕ И РУКАВА В СБОРЕ |
RUS |
ГОСТ ISO 2230-2013 |
ИЗДЕЛИЯ РЕЗИНОВЫЕ |
RUS |
ГОСТ ISO 1307-2013 |
РУКАВА РЕЗИНОВЫЕ И ПЛАСТИКОВЫЕ |
RUS |
ФИТИНГИ И ТРУБНЫЕ СОЕДИНЕНИЯ |
||
DIN EN 10226-1 |
Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
ENG |
DIN EN ISO 6708 |
Pipework components - Definition and selection of DN (nominal size) |
ENG |
DIN 3852-2 |
Stud ends and ports of fittings, valves and plug screws - Part 2: Dimensions for pipe thread |
ENG |
DIN 2353 |
Non-soldering compression fittings with cutting ring - Complete fittings and survey |
ENG |
DIN EN ISO 6708 |
Pipework components - Definition and selection of DN (nominal size) |
ENG |
DIN 3861 |
Non-soldering compression fittings - Compression rings - Design |
ENG |
SAE J514_201201 |
Hydraulic Tube Fittings |
ENG |
SAE J516_202111 |
Hydraulic Hose Fittings |
ENG |
ГОСТ 8.579-2019 |
ТРЕБОВАНИЯ К КОЛИЧЕСТВУ ФАСОВАННЫХ ТОВАРОВ ПРИ ИХ ПРОИЗВОДСТВЕ, ФАСОВАНИИ, ПРОДАЖЕ И ИМПОРТЕ |
RUS |
ГОСТ 7566-2018 |
МЕТАЛЛОПРОДУКЦИЯ Правила приемки, маркировка, упаковка, транспортирование и хранение |
RUS |
ГОСТ 22642-88 |
АРМАТУРА ТРУБОПРОВОДНАЯ ШЛАНГОВАЯ |
RUS |
ГОСТ 13682-80 |
МЕСТА ПОД КЛЮЧИ ГАЕЧНЫЕ |
RUS |
ГОСТ 6111-52 |
РЕЗЬБА КОНИЧЕСКАЯ ДЮЙМОВАЯ С УГЛОМ ПРОФИЛЯ 60° |
RUS |
ГОСТ 24705-2004 (ИСО 724:1993) |
Основные нормы взаимозаменяемости |
RUS |
ГОСТ 9544-2015 |
Арматура трубопроводная |
RUS |
ГОСТ 15763-2005 |
СОЕДИНЕНИЯ ТРУБОПРОВОДОВ РЕЗЬБОВЫЕ И ФЛАНЦЕВЫЕ НА PN () до 63 МПа (до 630 кгс/см ) Общие технические условия |
RUS |
ISO 8434-1:2018 |
Metallic tube connections for fluid power and general use — Part 1: 24° cone connectors |
ENG |
ISO 8434-2:2007 |
Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
ENG |
ISO 8434-3:2005 |
Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
ENG |
ISO 8434-6:2009 |
Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring |
ENG |
ISO 12151-1:2010 |
Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends |
ENG |
ISO 12151-2:2003 |
Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings |
ENG |
ISO 228-1:2000 |
Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
ENG |
ISO 7-1:1994 |
Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation |
ENG |
ГИДРАВЛИЧЕСКИЕ ТРУБЫ |
||
DIN EN 10305-1 |
Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
ENG |
DIN EN 10305-4 |
Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
ENG |
ОБОРУДОВАНИЕ И ИСПЫТАНИЯ |
||
ГОСТ 15150-69 |
МАШИНЫ, ПРИБОРЫ И ДРУГИЕ ТЕХНИЧЕСКИЕ ИЗДЕЛИЯ |
RUS |
ГОСТ 33272-2015 |
МЕЖГОСУДАРСТВЕННЫЙ СТАНДАРТ |
RUS |
ГОСТ ISO 6803-2013 |
РУКАВА РЕЗИНОВЫЕ ИЛИ ПЛАСТИКОВЫЕ И РУКАВА В СБОРЕ |
RUS |
ГОСТ Р ИСО 1402-2019 |
РУКАВА РЕЗИНОВЫЕ И ПЛАСТИКОВЫЕ И РУКАВА В СБОРЕ |
RUS |